Accessories

On this page (quick links):

Saddle
Slotted Screw Driver
Hex-Key Wrench
Set pin
Adhesive
Fiber Protector Cutting Tool
Fiber Protector Electric Cutting Tool


 

SaddleSaddle

Saddle

Feature:

  • Used for anchoring tube/conduit (holds down both tube and End Cap)

Material:

  • Polished steel plating

Notes:

  1. Apply tape to the tube to make a larger diameter if too loose
  2. Select saddle with dimension (A) in fig. 21 larger than the OD of required tube
  3. Also available in stainless steel


Pack: 100 pieces

Model A(mm) B(mm) C(mm) ÆD(mm) Matching Tube
PZ0104 4 15.8 10 4.5 KS-2.2N · KS-2.6N
PZ0106 6 17.8 10 4.5 KS-3N · 3.2N · KS-4N
PZ0108 8 23.0 12 5.5 KS-5N · KS-6N
PZ0110 10 25.0 12 5.5 KS-7N · KS-8N
PZ0112 12 27.0 14 5.5 KS-9N
PZ0114 14 32.7 16 5.5 KS-10N
PZ0115 15 33.7 16 7.5 KS-11N
PZ0116 16 34.9 18 7.5 KS-13N
PZ0118 18 41.4 20 9.0 KS-14N
PZ0120 20 43.4 20 9.0 KS-15N
PZ1122 22 66.0 25 9.0
PZ1125 25 70.0 25 9.0 KS-22N
PZ1128 28 78.0 30 10.0
PZ1130 30 80.0 30 10.0 KS-25N

 


Slotted Screw Driver

Slotted Screw Driver

Feature:

  • For use with M2 screws


Model: D-M2

 


Hex-Key Wrench

Hex-Key Wrench

Feature:

  • For use with M2 hex-head lag screw


Model: DG-M2

 


Set pin

Set pin

Feature:

  • For fastening to sensor head, End Cap and Panel Connector

Material:

  • Raw steel + Stainless Steel Plating

Note: Screw size selected based on screw-type Sensor Head Connector Chart on Page 15, column F

Model Type of the tip Fig
M2 x 1.5L - Slotted screw A
M2 x 2L- Slotted screw B
M2 x 2.5L Hex Head Lag screw C
M2 x 4L Hex Head Lag screw C
M2 x 3L Hex Head Lag screw C

 

 


Adhesive

Adhesive

Feature:

  • Adhesive used to attach connector to tube/conduit/>

Material:

  • High Super-5

Notes:

  1. Apply adequate adhesive onto tube and screw on the connector.
  2. Allow at least 5 minutes for the glue to harden before using.
  3. Does not adhere to polyethylene, polypropylene, nylon, polyvinyl chloride (PVC), fluorocarbon resin, or rubber.

 

 Adhesive - Diagram

 


Fiber Protector Cutting Tool

Fiber Protector Cutting Tool

Feature:

For use in cutting tubes

Model: HG-175

Material:

Steel Alloy

Notes:

  1. Hold the cutter at a 90° angle to the tube and cut one pitch width (3~4mm).
  2. Trim around the circumference of the tube as shown in fig 2.

 

Fiber Protector Cutting Tool - Diagram


Fiber Protector Electric Cutting Tool

Fiber Protector Electric Cutting Tool

Features:

  • The tube is cut straight and clean.
  • Maximum cutting diameter 15.8mm
  • Comes with 5 extra blades

 

Model: S-2

 

Cookies make it easier for us to provide you with our services. With the usage of our services you permit us to use cookies.
More information Ok