On this page (quick links):
Saddle
Slotted Screw Driver
Hex-Key Wrench
Set pin
Adhesive
Fiber Protector Cutting Tool
Fiber Protector Electric Cutting Tool
Saddle
Feature:
- Used for anchoring tube/conduit (holds down both tube and End Cap)
Material:
- Polished steel plating
Notes:
- Apply tape to the tube to make a larger diameter if too loose
- Select saddle with dimension (A) in fig. 21 larger than the OD of required tube
- Also available in stainless steel
Pack: 100 pieces
| Model | A(mm) | B(mm) | C(mm) | ÆD(mm) | Matching Tube |
| PZ0104 | 4 | 15.8 | 10 | 4.5 | KS-2.2N · KS-2.6N |
| PZ0106 | 6 | 17.8 | 10 | 4.5 | KS-3N · 3.2N · KS-4N |
| PZ0108 | 8 | 23.0 | 12 | 5.5 | KS-5N · KS-6N |
| PZ0110 | 10 | 25.0 | 12 | 5.5 | KS-7N · KS-8N |
| PZ0112 | 12 | 27.0 | 14 | 5.5 | KS-9N |
| PZ0114 | 14 | 32.7 | 16 | 5.5 | KS-10N |
| PZ0115 | 15 | 33.7 | 16 | 7.5 | KS-11N |
| PZ0116 | 16 | 34.9 | 18 | 7.5 | KS-13N |
| PZ0118 | 18 | 41.4 | 20 | 9.0 | KS-14N |
| PZ0120 | 20 | 43.4 | 20 | 9.0 | KS-15N |
| PZ1122 | 22 | 66.0 | 25 | 9.0 | — |
| PZ1125 | 25 | 70.0 | 25 | 9.0 | KS-22N |
| PZ1128 | 28 | 78.0 | 30 | 10.0 | — |
| PZ1130 | 30 | 80.0 | 30 | 10.0 | KS-25N |
Slotted Screw Driver
Feature:
- For use with M2 screws
Model: D-M2
Hex-Key Wrench
Feature:
- For use with M2 hex-head lag screw
Model: DG-M2
Set pin
Feature:
- For fastening to sensor head, End Cap and Panel Connector
Material:
- Raw steel + Stainless Steel Plating
Note: Screw size selected based on screw-type Sensor Head Connector Chart on Page 15, column F
| Model | Type of the tip | Fig |
| M2 x 1.5L - | Slotted screw | A |
| M2 x 2L- | Slotted screw | B |
| M2 x 2.5L | Hex Head Lag screw | C |
| M2 x 4L | Hex Head Lag screw | C |
| M2 x 3L | Hex Head Lag screw | C |
Adhesive
Feature:
- Adhesive used to attach connector to tube/conduit/>
Material:
- High Super-5
Notes:
- Apply adequate adhesive onto tube and screw on the connector.
- Allow at least 5 minutes for the glue to harden before using.
- Does not adhere to polyethylene, polypropylene, nylon, polyvinyl chloride (PVC), fluorocarbon resin, or rubber.
Fiber Protector Cutting Tool
Feature:
For use in cutting tubes
Model: HG-175
Material:
Steel Alloy
Notes:
- Hold the cutter at a 90° angle to the tube and cut one pitch width (3~4mm).
- Trim around the circumference of the tube as shown in fig 2.
Fiber Protector Electric Cutting Tool
Features:
- The tube is cut straight and clean.
- Maximum cutting diameter 15.8mm
- Comes with 5 extra blades
Model: S-2